| Del nr | Tillverkare | Ansökan |
|---|
| MAX1478C/D | MaximIC | 1% accurate, digitally trimmed, rail-to-rail sensor signal conditioner. |
| MAX6317HUK41DW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 4.100V, min reset timeout 1.12sec, typ watchdog timeout 6.3ms |
| MAX6321HPUK29DY-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 2.930V, reset timeout(min) 1.12sec, watchdog timeout(typ) 1.6sec |
| MAX361EPE | MaximIC | Precision, quad, SPST analog switch. |
| MXD1000SA100 | MaximIC | 5-tap silicon delay line |
| MAX877ESA | MaximIC | Step-up/step-down DC-DC converters |
| MAX6315US32D2-T | MaximIC | Open-drain microprocessor reset circuit. Reset threshold(nom) 3.20V. Reset timeout period(min) 20ms. |
| ICL7616DCTV | MaximIC | Single operational amplifier, 15mV |
| MAX6316MUK34AY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 3.400V, min reset timeout 1ms, typ watchdog timeout 1.6sec |
| MAX6319MHUK29A-T | MaximIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 2.930V, reset timeout(min) 1ms |
| MAX8214BCPE | MaximIC | Five universal voltage monitor - complete microprocessor voltage monitoring. Active pull-up outputs. |
| MXD1000UA60 | MaximIC | 5-tap silicon delay line |
| MAX464CNI | MaximIC | Two-channel, quad RGB switch and buffer. Voltage gain 1V/V. |
| MAX3488CPA | MaximIC | 3.3V-powered, 10Mbps and slew-rate-limited true RS-485/RS-422 transceiver. Guaranteed data rate 0,25Mbps. Supply voltage 3.0V to 3.6V |
| MAX6316LUK48BW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 4.800V, min reset timeout 20ms, typ watchdog timeout 6.3ms |
| MAX4278EUA | MaximIC | 310MHz -3dB bandwidth, gain of +2, closed-loop buffer. |
| REF01EP | MaximIC | +10V precisioon voltage reference. Max TEMPCO 8.5 ppm/degC. Initial error +-30mV |
| MAX6331SUR-T | MaximIC | Precision shunt regulator with reset. Reset threshold 2.78V, shunt regulator voltage 3.0V |
| MAX3869EHJ | MaximIC | +3.3V, 2.5Gbps, SDH/SONET, laser driver with gurrent monitor and APC. |
| MAX245EPL | MaximIC | +5V-powered, multichannel RS-232 driver-receiver. |
| MAX4533CAP | MaximIC | Quad, Rail-to-Rail, fault-protected, SPDT analog switch. |
| MAX5544CSA | MaximIC | Low-cost, +5V, serial-input, voltage-output, 16-bit DAC |
| MAX4587EUB | MaximIC | Serially controlled, 4-to-1 channel audio/video multiplexer. |
| MAX6318LHUK36AX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 3.600V min, reset timeout 1ms,typ watchdog timeout 102ms |
| MAX268BCNG | MaximIC | Pin programmable univesal and bandpass filter. Accuracy 2%. |
| MAX313ESE | MaximIC | 10Om, quad, SPST, CMOS analog switch |
| MAX1688EUE | MaximIC | Step-up DC-DC converter with precise, adaptive current limit for GSM. |
| MAX6316LUK43AZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 4.300V, min reset timeout 1ms, typ watchdog timeout 25.6sec |
| MAX247C/D | MaximIC | +5V-powered, multichannel RS-232 driver-receiver. |
| IH5142CWE | MaximIC | Low power fast CMOS analog switch. Single pole, doube throw (SPDT). |
