| Del nr | Tillverkare | Ansökan |
|---|
| MAX6312UK28D3-T | MaximIC | Multiple-input, programmable reset IC(push/pull reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual-reset input). Factory-trimmed reset thresholds 2.730(min) 2.870(max). Nominal timeout period 140ms. |
| MX7528JN | MaximIC | CMOS dual 8 bit buffered multiplying DAC. +5V to 15V single supply operation. Error +-1 LSB. |
| MAX4372FEUK-T | MaximIC | Low-cost, micropower, high-side current-sense amplifier with voltage output. +50V/V gain. |
| MAX456EQH | MaximIC | 8 x 8 video crosspoint switch. |
| MAX6125EUR | MaximIC | Low-cost, low-dropout, 3-terminal voltage reference. Preset output voltage 2.5V |
| MAX487CPA | MaximIC | Low-power, slew-rate-limited RS-485/RS-422 transceiver. Half-duplex. Data rate 0.25Mbps. Slew-rate limited - yes. Low-power shutdown - yes. Receiver/driver enable - yes. Quiescent current - 120 microA. Number of transmitter on bus - 128. |
| MAX6352MRUT-T | MaximIC | Dual-voltage microprocessor supervisory circuit with manual reset. Reset threshold 4.38V (Vcc5) and 2.63V (Vcc3). Active-low open-drain reset. |
| DG423DJ | MaximIC | Improved low-pover, CMOS analog switches with latches |
| MAX4275BJEUA | MaximIC | Dual, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 49, 1+ (Rf/Dg) noninverting gain 50, -3dB BW 310kHz. |
| MAX6322HPUK28D-T | MaximIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 2.800V, reset timeout(min) 1120ms |
| SI7661C/D | MaximIC | CMOS voltage converter |
| MX7535BD | MaximIC | Microprocessor-compatible, 14-bit DAC. INL +-1 LSB. |
| MXD1000UA25 | MaximIC | 5-tap silicon delay line |
| MAX197BEWI | MaximIC | Multi-range (+10V, +5V, +10V, +5V), single +5V, 12-bit DAS with 8+4 bus interface |
| MAX6343TUT-T | MaximIC | Microprocessor reset circuit with power-fail comparator. Reset threshold 3.08V. Open-drain active-low reset output, manual-reset input. |
| MAX792SCSE | MaximIC | Microprocessor and non-volatile metory supervisory circuit. Reset threshold 2.91V |
| MAX468C/D | MaximIC | Two-channel, quad video buffer. Voltage gain 1V/V. |
| MAX864EEE | MaximIC | Dual-output charge pump with shutdown |
| DG300CJ | MaximIC | Dual, TTL compatible CMOS analog switche |
| MAX4275BNEUA | MaximIC | Dual, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 99, 1+ (Rf/Dg) noninverting gain 100, -3dB BW 230kHz. |
| MAX145AEUA | MaximIC | +2.7 V, low-power, 2-channel, 108 ksps, serial 12-bit ADC. INL(LSB) +-0.5. |
| MAX6320PUK50AW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 5.000V, reset timeout(min) 1ms, watchdog timeout(typ) 6.3ms |
| MAX6316MUK25BZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 2.500V, min reset timeout 20ms, typ watchdog timeout 25.6sec |
| MAX6321HPUK44CZ-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 4.390V, reset timeout(min) 140ms, watchdog timeout(typ) 25.6sec |
| MAX6313UK40D2-T | MaximIC | Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc, 1 additional undervoltage reset input,negative/overvoltage reset input).Factory-trimmed reset thresholds 3.900(min) 4.100(max).Nominal timeout period 20ms. |
| MAX3760ESA | MaximIC | 622Mbps, low-noise transimpedance preamplifier for LAN and WAN optical receivers. |
| DG509ACWE | MaximIC | Monolithic CMOS analog multiplexer. Differential 4-channel (2-of-8). |
| MAX281ACPA | MaximIC | 5th-order, zero-error, bessel lowpass filter. |
| MAX6319LHUK45A-T | MaximIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-low,push/pull and active-high, push/pull).Factory-trimmed reset threshold(typ) 4.500V, reset timeout(min) 1ms |
| MAX799EPE | MaximIC | Step-down controller with synchronous rectifier for CPU power. 3.3V/5V or adjustable main output. Regulates negative secondary voltage (such as -5V). |
