| Del nr | Tillverkare | Ansökan |
|---|
| MAX6318MHUK35DY-T | MaximIC | "Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.500V, reset timeout(min) 1.12sec, watchdog timeout(typ) 1.6sec" |
| MAX4535ESD | MaximIC | "Fault-protected, high-voltage, dual 2-to-1 multiplexer operated with +-4.5V to +-20V dual supply or a +9V to +39V single supply." |
| MXD1013PA045 | MaximIC | 3-in-1 silicon delay line. Output delay 45ns. |
| MAX6337US25D3-T | MaximIC | "Ultra-low-voltage, low-power microprocessor circuit with manual reset (reset output active-low, open-drain) . Reset threshold(typ) 2.5V, reset timeout(min) 100ms." |
| MAX132ENG | MaximIC | "+,- 18-Bit ADC with serial interface" |
| MAX521ACAG | MaximIC | "Octal, 2-wire serial 8-bit DAC with Rail-to-Rail, unbuffered outputs. TUE(LSB) 1." |
| MAX758AC/D | MaximIC | "Adjuistable, step-down, current-mode PWM regulator. Inputs from 4V to 16V, up to 750mA load currents." |
| MAX808NEPA | MaximIC | Supervisory circuit with +-1.5% reset accuracy. Reset threshold(typ) 4.575V. CMOS RAM write protection.. |
| MAX6316MUK39DY-T | MaximIC | "Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 3.900V, min reset timeout 1120ms, typ watchdog timeout 1.6sec" |
| MAX350EPN | MaximIC | "Serially controlled, low-voltage, dual 4-channel multiplexer" |
| MAX311CPE | MaximIC | "CMOS RF/video multiplexer (2-of-8, 4 channel differential)." |
| ICL7652CPA | MaximIC | Chopper-stabilized operational amplifier |
| MAX6317HUK33CX-T | MaximIC | "Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 3.300V, min reset timeout 140ms, typ watchdog timeout 102ms" |
| MAX6105EUR-T | MaximIC | "Low-cost, micropower, low-dropout, high-output-current, SOT23 voltage reference. Output voltage 5.000V, input voltage range (Vout + 200mV)V to 12.6V to 12.6V." |
| MXD1000PD25 | MaximIC | 5-tap silicon delay line |
| DG387CK | MaximIC | General purpose CMOS dual analog switch. |
| REF01EZ | MaximIC | +10V precisioon voltage reference. Max TEMPCO 8.5ppm/degC. Initial error +-30mV |
| HI1-0201-9 | MaximIC | Quad SPST CMOS analog switch |
| MAX7232AFIQ | MaximIC | Triplexed LCD decoder/driver (10 digits/7 segments; serial input format; 2 annunciators per digit) |
| MAX4124EUK | MaximIC | "Single, wide-bandwidth, low-power, single-supply Rail-to-Rail I/O op amp. BW 25MHz." |
| MXD1013PA015 | MaximIC | 3-in-1 silicon delay line. Output delay 15ns. |
| MAX393MJE | MaximIC | "Precision, quad, SPST analog switch" |
| MAX4581ESE | MaximIC | "Low-voltage, CMOS analog multiplexer (8-channel)." |
| MAX708SMJA | MaximIC | "Low-cost, microprocessor supervisory circuit. Precison supply-voltage monitor 2.93V. Active-low and active-high reset output signal." |
| MAX180ACQH | MaximIC | "Complete, 8-channele, 12-bit data-acquisition system. Error(LSB) +-1/2." |
| MAX4590CWE | MaximIC | "1.25om, dual SPST, CMOS analog switch. Two NO (normally open) switches." |
| MAX232AEWE | MaximIC | "+5V-powered, multichannel RS-232 driver-receiver." |
| MAX3288CUE | MaximIC | "3.0V to 5.5V, 1.25Gbps LAN laser driver." |
| MAX509AEPP | MaximIC | "Quad, serial 8-bit DAS with Rail-to-Rail output. TUE (LSB) +-1" |
| MAX920EUK-T | MaximIC | "1.8V, nanopower 380nA, Beyond-the-Rails comparator. Open-drain output." |
